Well-prepared solutions for your projects.

Case studies

Conbit has been involved in a wide range of projects, offers specialised equipment and solutions, and can provide you with special services as described on this website. Here you will find a variety of case studies that illustrate the high quality you can expect when working with Conbit.

You can filter the list by selecting our main markets: oil & gas, wind energy, petrochemical or telecom. You can also filter by service area: lifting projects, lifting equipment or towers and stacks. An extra filter is location. You can also type in a specific search word or string.

Case Studies filtered for: Oil & Gas

Clear filters

Flare-tip windshroud replacement – Malaysia

Conbit delivered the lifting engineering, crew and lifting equipment, as well as the offshore execution of the wind shroud replacement and flare tip maintenance works.

Baronia BNCPP-B Flare-Tip Handling System – Retractable Davit

Conbit prepared the structural design of the flare-tip handling system, which featured a retractable davit as the main lifting equipment. And delivered the lifting equipment

Offshore Flare Tip Replacement – Malampaya

Well prepared offshore flare tip replacement in the West Philippine Sea

Challenging flare tip replacement – Bongkot North

Thanks to its vast expertise in flare-tip replacement, the Conbit and CR Asia team managed to complete the operation successfully, safely and ahead of schedule.

Flare tip replacement ANOA AGX

Contract for the replacement services of the flare tip, including the required engineering and the actual replacing of the existing flare tip with a new flare tip, which was supplied by Kotaminyak.

Offshore lifting: Living quarters Total K6-P

Creating lifting capacity outside the reach of the deck crane, without requiring a designated lifting vessel, is a challenge Conbit loves to take on. Conbit was awarded a contract for lifting two offshore accommodation units on the K6-P [...]

Offshore helideck replacement

Total E&P requested Conbit to provide its lifting expertise to replace the helideck on the F15-A platform.

Offshore installation of a PAU (Pre-assembled unit)

Successful offshore transport and installation: Pre Assemble Unit

Lifting of Lay Down Area Extension – Total E&P North Sea

Because the available deck crane could not be used for this lifting operation, Conbit was asked to provide a solution.

Mabruk shelter and helideck installation BD-1

Installation of an emergency shelter and helideck on the BD-1 offshore platform of Mabruk Oil Operations by Total and NOC.

Hook up support of topside for offshore platform

Conbit was contracted to engineer lifting plans and execute lifting operations during an offshore installation campaign.

Offshore diesel tank replacement Euro platform

Venko Offshore awarded Conbit a contract for the offshore replacement of two diesel storage tanks on the Euro platform located in the Dutch sector of the North Sea

Offshore cooler replacement J6A platform

Centrica awarded Conbit a contract for lifting and project management services that were necessary in replacing four coolers on their J6A platform

Agbami flare works and flare tip replacement

The flare tip replacement on the Agbami FPSO of Chevron Nigeria Limited, is another example of a successful combination of engineering, preparation and 0n-site construction.

Offshore flare tip replacement and maintenance activities – Dana Hanze North Sea

Conbit was awarded the contract to perform maintenance activities on the flare installation of Dana’s Hanze platform. One of the main activities was to design a flare tip handling system which can replace the HP flare tip (weight: 536 kg) [...]

Flare tip handling study for offshore platform

Conbit was requested by GBA to provide the basic and detailed engineering for a flare tip handling system design.

GSP Saturn – King Post Load Test

Conbit designed the load test configuration, supplied and installed the necessary equipment and performed the load test.

Offshore rigging – Separator replacement

Conbit provided its offshore rigging expertise to replace a separator on the deck of the F15-A platform.

Below-deck lifting: Offshore storage tank replacement

Venko Offshore awarded Conbit a contract for the offshore replacement of two diesel storage tanks. Conbit was given this project because of our below-deck lifting know-how and extensive experience in offshore operations

Offshore crane exchange GAZ de France L10-A North Sea

Conbit provided the best solution in terms of structural design and procedures for offshore crane exchange.

OFON2 Flare Tip Replacement

Replaced the flare tip on the OFON2 complex, offshore Nigeria. A team of 5 people completed the job within a limited shutdown period.

Offshore crane replacement L10-E

Conbit performed a combination of structural design, lifting and mechanical works for the crane replacement on the L10-E well protector platform in the North Sea.

Conbit supports Centrica with lift below helideck

Below deck lift of an offshore platform directly from a supply vessel. Conbit delivered installation engineering & installation of oil tank under helideck

Flare Tip Handling Kit

The flare tip handling kit allows future flare tip replacements with a system which is available in the operator’s warehouse.

Helideck perimeter netting installation

Conbit installed Frictape helideck perimeter netting on a Dana Petroleum’s platform in the North Sea in just 10 days.

Grillage & seafastening

Holstein North module grillage & seafastening.

Bongkot Flare Tip Replacement

Flare tip replacement on the Bongkot platform together with the team of its local partner, CR Asia.

F15-A Lifting Services During Shutdown

Conbit supplied lifting assistance in many lifting and rigging activities such the helideck, water treatment and injection facility and a separator.

Offshore flare tip repair works

Repair works on the flare tips and access platform of FPSO Girassol. The project included the supply of specialised equipment and the offshore works.

Modular Lifting System

Standardized temporary offshore lifting systems with a capacity of 5-45 tonnes allows the installation of modules and components outside the reach of the platform crane.

Crane Boom Tip Replacement Offshore

Conbit coordinated the complete installation of the new crane boom tip on the L7P platform for Total E&P Netherlands.

Successful subsea tree installation on the North Sea

Conbit assisted with the safe and efficient lifting of a subsea tree, performed directly from a supply vessel with relatively sensitive equipment.

Offshore Skidding of Compressor Module

Conbit performed the skidding and jacking operations to install the 340mT compression module on the GDF E17a-A platform in the Dutch sector of the North Sea.

ALBA B3 Flare tip replacement

For the Alba-B3 compression platform Conbit delivered an exchange proposal and flare tip handling method for the future operation.

FPSO stair tower

FPSO Saxi Batuque Stair Tower.

Helideck structural analysis

Conbit is providing the servicing and checks for existing helidecks with S-92 helicopters for approvals by DNV or Lloyds.

Topside concept design

Offshore lift entrusted to Conbit

Design and engineering of a dedicated lift solution for the installation of a deck extension on the K2b-A platform to facilitate a coil tubing job.

Offshore Helideck Service

Conbit’s engineers and technicians have worked on many offshore helidecks and have seen the development over the years.

YOUR PARTNER IN LIFTING PROJECTS, LIFTING EQUIPMENT AND TOWERS/STACKS

Contact Us

We are not around right now. But you can send us an email and we will get back to you as soon as possible.

Not readable? Change text.

Start typing and press Enter to search